As they have done round after round of press testing both with the ZERO and other presses AREA 419 has known that the very best way to get consistent sizing time and again is to have contact between the shellholder and the die. This removes your ability however to dial in your shoulder bump - until now. With the ZERO Modular Shellholder System you can set up your shellholder to your die and have more consistency more repeatability and less hassle. It’s a win-win-win.Available in either a Zero specific mounting system or a traditional shellholder this allows you to dial in should bump with a set of 6 precision ground stainless steel inserts .002″ at a time.The Kit comes with:– A Base (meant for ZERO or Traditional presses your choice)– THREE Shellholder/Extractor tops sized for 223 (.384″ Bolt Face) 308 (.470″ Bolt Face) Standard Magnum (.540″ Bolt Face) or similar– SIX Precision Ground headspace inserts ranging from +.002″ to -.008″– Aluminum Storage Bloc

As they have done round after round of press testing both with the ZERO and other presses AREA 419 has known that the very best way to get consistent sizing time and again is to have contact between the shellholder and the die. This removes your ability however to dial in your shoulder bump - until now. With the ZERO Modular Shellholder System you can set up your shellholder to your die and have more consistency more repeatability and less hassle. It’s a win-win-win.Available in either a Zero specific mounting system or a traditional shellholder this allows you to dial in should bump with a set of 6 precision ground stainless steel inserts .002″ at a time.The Kit comes with:– A Base (meant for ZERO or Traditional presses your choice)– THREE Shellholder/Extractor tops sized for 223 (.384″ Bolt Face) 308 (.470″ Bolt Face) Standard Magnum (.540″ Bolt Face) or similar– SIX Precision Ground headspace inserts ranging from +.002″ to -.008″– Aluminum Storage Bloc

The first in a line of ARCA-mounted accessories for the rear of your ZERO the ZERO Storage Block is the perfect storage solution for the small tools shellholders and disparate parts that Area419 is sure are around your press. Featuring a hole specifically for your ZERO torque wrench and a magnet for attaching other tools they think it’ll help to clean up your bench and organize your gear.This tray is also ambidextrous and can be hung from either side of the ZERO with full functionality.

The Hunt scope rings are light rigid and able to hold onto an optic in a dramatic recoiling environment.NOTE: TO KEEP THE SIZE AND WEIGHT OF THESE RINGS TO A MINIMUM THERE ARE NO ACCESSORY ATTACHMENT POINTS ON THESE RINGS. 

The Hunt scope rings are light rigid and able to hold onto an optic in a dramatic recoiling environment.NOTE: TO KEEP THE SIZE AND WEIGHT OF THESE RINGS TO A MINIMUM THERE ARE NO ACCESSORY ATTACHMENT POINTS ON THESE RINGS. 

The Hunt scope rings are light rigid and able to hold onto an optic in a dramatic recoiling environment.NOTE: TO KEEP THE SIZE AND WEIGHT OF THESE RINGS TO A MINIMUM THERE ARE NO ACCESSORY ATTACHMENT POINTS ON THESE RINGS. 

The Hunt scope rings are light rigid and able to hold onto an optic in a dramatic recoiling environment.NOTE: TO KEEP THE SIZE AND WEIGHT OF THESE RINGS TO A MINIMUM THERE ARE NO ACCESSORY ATTACHMENT POINTS ON THESE RINGS. 

Powder drop tubes are used when trying to fill cases beyond what is normally achievable with extruded powders.  The longer drop combined with relatively small internal bore allows the kernels of powder to fill the case more fully. Tubes are for use only with the Area 419 Interchangeable head powder funnel system 3" Long Can be attached together to form any multiple of 3 length Caliber specific heads attach to the end of the drop tube Machined from solid 6061-T6 Aluminum Type II Anodized FUNNEL SHOWN NOT INCLUDED (sold separately)

This product listing is for a caliber specific funnel HEAD ONLY no funnel or billet storage block included. Please see “Master Kit" which includes six heads a handle and a storage block.The Area 419 billet aluminum powder funnel uses a system of interchangeable caliber specific heads to make it the ultimate funnel for reloaders available today.  Universal plastic powder funnels have several issues that are solved with this system.1.  Static cling plastic is prone to being charged with static and kernels of powder will stick to the walls causing you to have to tap the funnel to get them all to fall.2.  No such thing as universal.  There are always cases that just wont work well with the universal design and funnels tip off and spill powder or they just plain wont work.3.  Universal means that it has a hole meant for 22 caliber.  So if you are trying to dump 90 grains into a big magnum you are waiting a long time for the powder to fill.The Area 419 Funnel’s interchangeable heads thread onto the funnel and are neck diameter specific for each caliber (color coded to keep track of them).  The do not rely on fitting over the body of the case to hold in place.  They are sized slightly larger than the neck diameter so that they hold solid on the case.  Each head has a bore sized a few thousandths smaller than the bullet diameter so maximum flow is achieved for each caliber.  This is huge for the super ultra magnum guys (375 Cheytac 408 Cheytac 50 BMG etc).  The interface between the heads and the funnel is designed in such a way that no kernels can ever get stuck between the two as long as the head is tightened completely.The Funnel’s design is both aesthetic and performance driven.  Being machined from a solid billet of 6061-T6 aluminum means no static charge to cling kernels to the funnel walls.  This also makes it far safer for use with black powder. “Flutes” on the outside are for looks on the inside though they disturb the powder kernels from trying to jam up at the neck.  It also gives some airspace so they do not get packed up so tightly all aimed to increase flow through the nozzle. 3/8″ tall straight section at the top to help prevent kernels of powder from bouncing out when poured in. Smooth surfaces at the neck of the funnel and inside the heads promote quick flow and prevent any sticking kernels MADE IN USA From USA made aluminum on a USA made HAAS mill with USA made cutting tools

**Rear Fixed Barricade stop not includedMLOK HARDWARE NOT INCLUDEDRail Features:– Serrated rail sides interface with our proprietary clamp design to mechanically lock it in place so no movement is possible.  Serrations are not sharp will not damage bags or your hands.– Rail is backwards compatible with standard Arca accessories but will not be locking without our clamp– Rail is 10″ long giving you great real estate for attachments but not extending too far on shorter forends.  The best part is it still only weighs in at a paltry 3.5oz– Made to the RRS 1.5″ Dovetail Standard so you can be sure lever clamps will work– No sharp edges. Every corner is radiused and every edge is chamfered on the machine. This takes longer to make but it is the only right way.– While designed with Manners Composite Stocks in mind this rail accommodates a multitude of rifle and stock configurations that have an accessible front action screw and some sort of front attachment point(s).– Designed to attach to the rifle up to 4 places for maximum strength and stability.– Type 3 Hard Coat anodized for additional durability.– Made from 6061-T6 Aluminum– Made in-house here in the USA from USA sourced Aluminum on USA made CNCs– Rail comes with 1 long Remington 700-style action screw to fit the rail to the front action screw attachment point.  Some trimming will likely be required.– A 3/4″ paddle bit and drill press may be required for installation of tee-nuts depending on current rifle configuration.  Tee nuts and hardware included. 

 Rear angled barricade stop sold separately.THIS RAIL REQUIRES 6 CONSECUTIVE M-LOK SLOTS TO ATTACH. FOR STOCKS WITH FEWER M-LOK SLOTS YOU’LL WANT A 12″ UNIVERSAL RAIL WITH M-LOK ATTACHMENT NUTSArea 419 is always looking for ways to improve existing products when we are not developing new technologies. With the rapid growth in popularity of ARCA rails in precision rifle we saw a need to improve this great dovetail technology to something that could be mechanically locked in place instead of just friction.  If you have ever tried using a Barricade stop on an existing ARCA rail you’ve probably also seen it slide under much pressure.Introducing the ARCALOCK Dovetail Rail System *Rail is only locking with an Area 419 clamp*Rail Features:– Serrated rail sides interface with our proprietary clamp design to mechanically lock it in place so no movement is possible.  Serrations are not sharp will not damage bags or your hands.– Rail is backwards compatible with standard Arca accessories but will not be locking without our clamp– Rail is 12″ long giving you the entire length of the stock forend for attachments.  The best part is it still only weighs in at a paltry 4.1oz– Made to the RRS 1.5″ Dovetail Standard so you can be sure lever clamps will work– No sharp edges. Every corner is radiused and every edge is chamfered on the machine. This takes longer to make but it is the only right way.– Type 3 Hard Coat anodized for additional durability.– Made from 6061-T6 Aluminum– Made in-house here in the USA from USA sourced Aluminum on USA made CNCs– M-LOK Slots on underside of rail also allow you to attach any M-LOK accessories to the 419 Rail– Rail comes with all M-LOK mounting hardware

 Rear angled barricade stop sold separately.THIS RAIL REQUIRES 6 CONSECUTIVE M-LOK SLOTS TO ATTACH. FOR STOCKS WITH FEWER M-LOK SLOTS YOU’LL WANT A 12″ UNIVERSAL RAIL WITH M-LOK ATTACHMENT NUTSArea 419 is always looking for ways to improve existing products when we are not developing new technologies. With the rapid growth in popularity of ARCA rails in precision rifle we saw a need to improve this great dovetail technology to something that could be mechanically locked in place instead of just friction.  If you have ever tried using a Barricade stop on an existing ARCA rail you’ve probably also seen it slide under much pressure.Introducing the ARCALOCK Dovetail Rail System *Rail is only locking with an Area 419 clamp*Rail Features:– Serrated rail sides interface with our proprietary clamp design to mechanically lock it in place so no movement is possible.  Serrations are not sharp will not damage bags or your hands.– Rail is backwards compatible with standard Arca accessories but will not be locking without our clamp– Rail is 12″ long giving you the entire length of the stock forend for attachments.  The best part is it still only weighs in at a paltry 4.1oz– Made to the RRS 1.5″ Dovetail Standard so you can be sure lever clamps will work– No sharp edges. Every corner is radiused and every edge is chamfered on the machine. This takes longer to make but it is the only right way.– Type 3 Hard Coat anodized for additional durability.– Made from 6061-T6 Aluminum– Made in-house here in the USA from USA sourced Aluminum on USA made CNCs– M-LOK Slots on underside of rail also allow you to attach any M-LOK accessories to the 419 Rail– Rail comes with all M-LOK mounting hardware

**Rear Fixed Barricade stop not includedMLOK Hardware not included.Rail Features:– Serrated rail sides interface with our proprietary clamp design to mechanically lock it in place so no movement is possible.  Serrations are not sharp will not damage bags or your hands.– Rail is backwards compatible with standard Arca accessories but will not be locking without our clamp– Rail is 12″ long giving you the entire length of the stock forend for attachments.  The best part is it still only weighs in at a paltry 4.1oz– Made to the RRS 1.5″ Dovetail Standard so you can be sure lever clamps will work– No sharp edges. Every corner is radiused and every edge is chamfered on the machine. This takes longer to make but it is the only right way.– While designed with Manners Composite Stocks in mind this rail accommodates a multitude of rifle and stock configurations that have an accessible front action screw and some sort of front attachment point(s).– Designed to attach to the rifle up to 4 places for maximum strength and stability.– Type 3 Hard Coat anodized for additional durability.– Made from 6061-T6 Aluminum– Made in-house here in the USA from USA sourced Aluminum on USA made CNCs– Rail comes with extra Remington 700-style action screw of extended length to fit the rail to the front action screw attachment point.  Some trimming will likely be required.– A 3/4″ paddle bit and drill press may be required for installation of tee-nuts depending on current rifle configuration.  Tee nuts and hardware included.

NOTE: Rail kits now come with only one action screw and it is a longer screw. With the endless action/stock/chassis combos we found that nearly everyone was required to trim the screw for fitment anyway so the longer screw makes much more sense. MLOK HARDWARE IS NOT INCLUDED. Area 419 is always looking for ways to improve existing products when not developing new technologies. With the rapid growth in popularity of ARCA rails in precision rifle ARCA saw a need to improve this great dovetail technology to something that could be mechanically locked in place instead of just friction.  If you have ever tried using a Barricade stop on an existing ARCA rail you’ve probably also seen it slide under much pressure.Introducing the ARCALOCK Dovetail Rail System *Rail is only locking with an Area 419 clamp*Rail Features:– Universal rail design is the same footprint as our previous rail.  (There were two revisions to the hole spacing if you have a very early model your hole spacing may change)– Serrated rail sides interface with our proprietary clamp design to mechanically lock it in place so no movement is possible.  Serrations are not sharp will not damage bags or your hands.– 65 Locking positions available on the 14″ rail– Rail is backwards compatible with standard Arca accessories but will not be locking without our clamp– Serrated fixed rear barricade stop is same as before but now we include an extension plug to raise it by another 1/2″– Rail is 14″ long giving you the entire length of the stock forend for attachments.  The best part is it still only weighs in at a paltry 5.6oz– Made to the RRS 1.5″ Dovetail Standard so you can be sure lever clamps will work– No sharp edges. Every corner is radiused and every edge is chamfered on the machine. This takes longer to make but it is the only right way.– While designed with Manners Composite Stocks in mind this rail accommodates a multitude of rifle and stock configurations that have an accessible front action screw and some sort of front attachment point(s).– Spacers for rifle stocks with non-flat forends are available– Designed to attach to the rifle up to 4 places for maximum strength and stability.– Extends past the end of most rifle stocks allowing a further forward bipod attachment increasing stability.– Type 3 Hard Coat anodized for additional durability.– Made from 6061-T6 Aluminum– Made in-house here in the USA from USA sourced Aluminum on USA made CNCs– Rail comes with one Remington 700-style action screws of extended length to fit the rail to the front action screw attachment point.  Some trimming will likely be required.– A 3/4″ paddle bit and drill press may be required for installation of tee-nuts depending on current rifle configuration.  Tee nuts and hardware included.Rail Weights:14″: 156.03 Grams12″: 111.5 Grams10″: 95.2 Grams

For all those looking for the lightest smallest ARCALOCK rail on the market – here ya go. Weighing in at just 1.5oz this will fir forend hole spacings of 2″-3.5″ just like our extremely popular IBR. The rail will also come with t-nuts and hardware to allow you to install the rail closer to the magwell for tripod use.MLOK HARDWARE NOT INCLUDEDThese rails are made of 6061 billet aluminum and will be sold only in a black hardcoat anodized finish.

Rail Features:– Serrated rail sides interface with our proprietary clamp design to mechanically lock it in place so no movement is possible.  Serrations are not sharp will not damage bags or your hands.– Rail is backwards compatible with standard Arca accessories but will not be locking without our clamp– Rail is 6″ long and weighs in at a paltry 2.2oz– Made to the RRS 1.5″ Dovetail Standard so you can be sure lever clamps will work– No sharp edges. Every corner is radiused and every edge is chamfered on the machine. This takes longer to make but it is the only right way.– Type 3 Hard Coat anodized for additional durability.– Made from 6061-T6 Aluminum– Made in-house here in the USA from USA sourced Aluminum on USA made CNCs– Rail comes with all M-LOK mounting hardware

Rail Features:– Serrated rail sides interface with our proprietary clamp design to mechanically lock it in place so no movement is possible.  Serrations are not sharp will not damage bags or your hands.– Rail is backwards compatible with standard Arca accessories but will not be locking without our clamp– Rail is 6″ long and weighs in at a paltry 2.2oz– Made to the RRS 1.5″ Dovetail Standard so you can be sure lever clamps will work– No sharp edges. Every corner is radiused and every edge is chamfered on the machine. This takes longer to make but it is the only right way.– Type 3 Hard Coat anodized for additional durability.– Made from 6061-T6 Aluminum– Made in-house here in the USA from USA sourced Aluminum on USA made CNCs– Rail comes with all M-LOK mounting hardware

MLOK HARDWARE NOT INCLUDEDArea 419 is always looking for ways to improve existing products when we are not developing new technologies. With the rapid growth in popularity of ARCA rails in precision rifle we saw a need to improve this great dovetail technology to something that could be mechanically locked in place instead of just friction.  If you have ever tried using a Barricade stop on an existing ARCA rail you’ve probably also seen it slide under much pressure.Introducing the ARCALOCK Dovetail Rail System *Rail is only locking with an Area 419 clamp*Rail Features:– Serrated rail sides interface with our proprietary clamp design to mechanically lock it in place so no movement is possible.  Serrations are not sharp will not damage bags or your hands.– Rail is backwards compatible with standard Arca accessories but will not be locking without our clamp– Rail is 8″ long giving you the entire length of the stock forend for attachments.  The best part is it still only weighs in at a paltry 3 oz– Made to the RRS 1.5″ Dovetail Standard so you can be sure lever clamps will work– No sharp edges. Every corner is radiused and every edge is chamfered on the machine. This takes longer to make but it is the only right way.– Type 3 Hard Coat anodized for additional durability.– Made from 6061-T6 Aluminum– Made in-house here in the USA from USA sourced Aluminum on USA made CNCs– Fits a MPA CZ455 chassis with no modifications

NOTE: BECAUSE OF THE ADDITIONAL WIDTH OF THIS CLAMP IT IS NOT COMPATIBLE WITH ALL AREA 419 ARCALOCK DEVICES. THIS INCLUDES BUT IS NOT LIMITED TO: Garmin XERO Arms RailChanger X.Area 419 are big ARCALOCK people and think it’s the best solution for most people trying to shoot mid- to long-range.Area 419 also knows that there are still a lot of rifles out there with Pic sections on the front end or bipods that need to be used on both ARCA and Pic attachment points.Finally Area 419 has a clamp that can do both – the ARCALOCK Dual Clamp.Precision milled from aerospace grade 6061-T6 aluminum and stainless steel this Dual Clamp is versatile adjustable feature-rich and 100% American Made Adjustable tension to ensure a great fit on either mounting surface “On/Off” ARCALOCK switch for ideal fitment on either Area 419 ARCALOCK Rails or ARCA rails from other manufacturers Hardened steel pins and grabbers for exceptional picatinny lock-up ARMS 17S attachment for use with common bipods from Atlas Thunderbeast MDT Magpul Harris (with adapter) and more!

Along with the ZERO Storage Tray we wanted a deeper tray to hold bullets or some other random goodies. This tray is meant to hang from the front of the Storage tray like an Akro bin but is also shipped with rubber feet for placing on your loading bench. The tray is 4″x4″x1.5″ and can comfortably hold about 150 6mm projectiles. 

Multi tasking at its finest*!  Add more 419 Bling to your bench with this billet aluminum tray for holding bullets while you are reloading.  Also we threw a notch in the edge to use it as a cigar ash tray – comfortable holding cigars with ring sizes into the mid-50’s.Available in Clear anodized finish for durability and consistency.*If you smoke while reloading don’t do that. Gunpowder tends to get a little testy to deal with around fire.

Area 419 Billet Anodized Loading block. The same awesome loading block you’ve come to love from us just anodized to hold up to all your abuse better.50 places of 308 Magnum or Lapua bolt faced rounds.  Features rubber pads on the bottom to keep from sliding around.Block is machined in house from 6061-T6 Aluminum.  Dimensions are 9.5″ x 4″ x 5/8″.  Holes are 0.500″ deep and are a tight fit around the case to prevent tipping over.  Hole bottoms have a small “divot” in the very center to catch powder kernels and prevent any possible accidents with primers.HOLE DIAMETERS 223 – (0.390″)

Area 419 Billet Anodized Loading block. The same awesome loading block you’ve come to love from us just anodized to hold up to all your abuse better.50 places of 308 Magnum or Lapua bolt faced rounds.  Features rubber pads on the bottom to keep from sliding around.Block is machined in house from 6061-T6 Aluminum.  Dimensions are 9.5″ x 4″ x 5/8″.  Holes are 0.500″ deep and are a tight fit around the case to prevent tipping over.  Hole bottoms have a small “divot” in the very center to catch powder kernels and prevent any possible accidents with primers.HOLE DIAMETERS 308 – (0.485″)

Area 419 Billet Anodized Loading block. The same awesome loading block you’ve come to love from us just anodized to hold up to all your abuse better.50 places of 308 Magnum or Lapua bolt faced rounds.  Features rubber pads on the bottom to keep from sliding around.Block is machined in house from 6061-T6 Aluminum.  Dimensions are 9.5″ x 4″ x 5/8″.  Holes are 0.500″ deep and are a tight fit around the case to prevent tipping over.  Hole bottoms have a small “divot” in the very center to catch powder kernels and prevent any possible accidents with primers.HOLE DIAMETERS Lapua – (0.600″)

Area 419 Billet Anodized Loading block. The same awesome loading block you’ve come to love from us just anodized to hold up to all your abuse better.50 places of 308 Magnum or Lapua bolt faced rounds.  Features rubber pads on the bottom to keep from sliding around.Block is machined in house from 6061-T6 Aluminum.  Dimensions are 9.5″ x 4″ x 5/8″.  Holes are 0.500″ deep and are a tight fit around the case to prevent tipping over.  Hole bottoms have a small “divot” in the very center to catch powder kernels and prevent any possible accidents with primers.HOLE DIAMETERS Magnum – (0.560″)